Why use a dishwasher?

I’m lazy! There I said it, here’s my life hack for the method I use that should make you think why use a dishwasher?

I prefer this method, simply because I live alone, this is the approach that I use. It works for me. I live alone, but I have a habit of grabbiing a new piece of kitchenware rather than wash the last. I then just tend to wash everything all together, the end result being I ended up developing my own pattern for doing things which gives me free time.

I do actually wash dishes individually from time to time. I just get distracted a lot, and prefer to grab a new one from the cupboard than to clean an old one to reuse it. Don’t ask me why, just seems a pointless idea. If I only owned 1 dish, 1 cup etc then I’d be forced to wash them all the time. Maybe adopting a minimalist lifestyle would work for me, but this is the approach I use and I’m fine with it.

If I can find a way of doing something quicker, I will. Lazy people find the most efficient way of doing things, it’s a fact. We will figure out a fast way of doing something so we can spend more time being lazy.

Here’s my Life Hack. Which is the reason I rarely use a dishwasher, firstly it takes forever, secondly, it’s more expensive. Lastly, it never used to get into every nook and cranny no matter how I cleaned it. So it was a waste of time anyway. Dishwashers rely on you getting rid of the the dirty stuff on a plate so it can clean off the lighter stuff. What’s the point in that. If you’re going to clean something and replace the manual labour of it, then you should do a better job. Dishes, everyone hates them and doing them. If you love them, I think you’re a Psychopath… you weirdo you! Joking, whatever makes you happy, but I can think of other things.

My time is precious to me. As a person I’m lazy, I know I am. I didn’t really develop the right mindset and mentality to clean as I go, so I’ve had to make up my own. Either that, or I just can’t be arsed doing things and just prefer doing things my own way. Which sounds more like me.

Anyway, I normally do my dishes when there’s a full load. I hate doing them one at a time, that’s just the way I am. Seems a waste of effort. I used to use Dishwasher, but it’s expensive.

A quick google search suggests a Dishwasher uses about 1.5KWh of Electricity per cycle (about 20p of Electric), you then have to factor in the tablets for materials, you’re probably looking at around 50p for every cycle. Not good.

My method that I use which makes dishwasher inefficient, and is a faster, cheaper and easier way to wash dishes.

METHOD

  • Run the tap until boiling hot, plug the sink and give it a squirt of good ol’ Fairy liquid for some bubble magic
  • Chuck in a full sink of your washing inside it and leave it to sit for about an hour or so.
  • When the water is cooler, take out the items one at a time and scrub them down/clean them, empty sink
  • Fill the kettle with water to the max and boil it. When the kettle is boiled, put them all back in the sink
  • Pour boiling water over it all, and dry them off / put away

That’s it, simple!

PERKS and reasons why you should consider doing this

  • Less work, all you have to do is quickly scrub them and dry them
  • It’s faster to dry , because the boiling water is 100’c, essentially instantly dries so there’s very little to clean
  • It frees up your time, it gives you time tocus on other chores around the home, or just reading a book
  • It’s cheaper (a full kettle costs 2.5p to boil) and Fairy liquid about £3 and lasts forever.

As you can see, this is the reason I clean this way. When you’re pressed for time, a Dishwasher might help. However it costs you more. The method I use works for me, it’s cheaper than a dishwasher, and makes me more efficient at house work

if you don’t use this method, that’s your choice, just a life hack to help others out

Views – 16

DIY Aux Cable for Audi A3

The main (annoying) problem that I’ve had after changing to my Audi A3 Sportback is that my music options have been restricted. The Audi has an “Aux” input so that you can hook up an external Audio source to the car. Now here lies the problem(s)

#1 – I had to find a cable. No problem, rummaged through the old boxes, found one #Winner
#2 – Cable plugs into the Aux in car, when attempting to connect to the SamsungS7 it’s too small….. shit!
#3 – I don’t have an adapter cable for Samsung S7 to 3.5mm…. double shit!!

Now, I’m not one to admit defeat, so I needed a solution. Time to bodge it

  • Old pair of Samsung S7 Headphones – Check
  • One incompatible 3.5mm to 3.5mm Cable – Check
  • One person who likes to modify and hack stuff so it works. DAMN RIGHT!

Now, there’s one main problem even after all this. Which I don’t think is a problem as such, I think it’s just the design of the connectors (or I’ve soldered them wrongly). I’m going to mention it here however, just as a guidance note, and for future input if anyone who understands it better than me can clarify. Basically when soldered together, I used the multimeter to check for continuity between each individual connection. As they are isolated, there should be none except for the points. The Samsung S7 has one point which isn’t soldered anywhere which is the Mic connector.

POTENTIAL CAUTION
All the other three points I soldered from the TRS Jack to the TRRS Jack and their appropriate connectors. When I tested for continuity however, I get continuinty between Ground and the Right Channel on TRS/TRRS. I have grounds themselves, and the solder points are fine. So I’m not sure if I burned through the insulation, or if it’s because of the type of jacks I’m using. I did a quick search online, and the grounds themselves on diagrams are both linked up to the actual L/R channels anyway. The comments posted said there’s no issue soldering L/R to Ground, as long as you have continuity between the Grounds. I did so I’m happy with that. I’m just noting this here, so if anyone else attempts this modification, they’re aware of any potential risks or damage to their vehicle. I’m confident it won’t cause damage so I’m happy to continue using it.

Here’s how I made the Aux Cable. First I had to identify the connectors which correspond to the wires (Found here). So, the standard connector I have is a TRS (Balanced Mono) and the Samsung S7 appears to be a TRRS connector (Balanced Stereo). Get the old multimeter out, and run continuity tests between the individually isolated terminals, and their corresponding solder points/wires. This allowed me to identify the Ground, Mic, Left and Right Channels

Just as a note, I was intially going to solder to the wires. The cables in the Samsung S7 Headphone cable however are ridiculously thin. So I ended up snipping it until I got to the plug itself and soldered directly to the jack. Much nicer and looks way better in my opinion

Does it work? – Yes. I had to slightly fine tune mine as the balance was off slightly. I had to fade it to the left by 1 bar. Otherwise it’s nice and clear and loud now. I recommend turning your Volume up to it’s maximum on your phone after it’s plugged in, as it’s quiet when left on “normal” volumes.

If you are planning on making your own Aux Cable, I’d suggest buying TRRS connectors so that when you solder them it’s just a straight connection to connection, and each individual wire is isolated. Also for the cable, you’d need some kind of speaker cable with 3 cores (One for left, one for righ, one for ground).

If you’re here for the pictures of this modification, see below.

Just as a future note, this DID work, but it was only a temporary measure. I ended up buy an Aux Cable from eBay that was braided. Here’s a similar one on Amazon

Views – 42

How I fixed my washing machine for £15

Over time my washing machine has been developing a fault. I thought I had spilled water down the back of it because when I switched it on, every light on the front panel would flash continuously. Sometimes it would stop, and others it would just keep going and going.

This causes an issue when I’m trying to do my washing up, did some research because I got sick of it and discovered it’s actually a really common fault with washing machines (usually by Hotpoint / Creda / Ariston). The main capacitor on the electronics board (usually C17 Capacitor) has failed.

Board Inpsection

Damaged capacitors

To fix the issue it’s a case of replacing the capacitors. Reading horror stories on the internet suggests calling out a washing machine engineer, they would simply replace the board and reprogram it. Costing the end user around £150

The article that follows shows how I fixed my washing machine for £15

COMPONENTS NEEDED

  • Solder Wick (2.8mm x 1.5m)
  • Soldering Iron, Tip Cleaner & Solder
  • Replacement Capacitor(s) – They need to be ELECTROLYTIC
    • You will need to double check, but most likely it will be…
      • 25V / 100uF
      • 10V / 680uF
      • 10v / 470uF

Once you have verified the correct capacitors for your board you will need to remove them from the board. I’m not the best at soldering, so everyone has their own technique, not to mention the soldering iron I had was a really cheap one that didn’t heat up well. This is the technique I used

 

  • Cleaned the tip of the iron after heating
  • Apply a small amount of solder to the iron
  • Put the solder wick over the board around the capacitor leg and wick it up
  • Keep repeating the procedure until the leg is free, clean iron each time

It’s hard to describe the wicking process, but basically having the extra solder on the iron seems to increase the heat and make it easier to wick the hold solder off. Don’t bother with those plunger removers, they’re just annoying. Use the reel and it will be all off really quickly. In terms of cleaning the tip I used one of those metallic pan scrubbers you get from Asda (the balls of metal) what you use for cleaning stainless steel. The true kits use brass balls, but for cheap soldering irons I don’t really care. It worked well

 

Once you have removed the solder from all the pins, remove the capacitors. Insert the replacement capacitors inside the holes you made which should be clean, making sure you align (+ to +) and (- to -). You should find that there is a small white circle for the negative side and a + mark on the board for positive. Also on the capacitor the negative side there will be lines down the side. If there are no lines, the “shorter” leg of the capacitor is the negative side

 

 

After you have inserted a capacitor, tip the board upside down. Clean the tip of the iron, and let the end hit up (to the point where solder melts on touch), clean the tip again so it’s shiny. Then hold the hot point of the iron to the metal leg of the capacitor and touch the solder onto it, you should find the solder melts. Apply a small amount of solder so it covers the peg and then remove the solder, then remove the iron (this entire process should only take 2 or 3 seconds).

Soldering capacitors

Soldering new caps

Clean the iron tip each time, and reapply solder to all the board points. Once you have resoldered all the connectors onto the board, snip off the end metal pieces with scissors / pliers. Your work should then be complete

Installed capacitors

The new capacitors installed

Now you just need to test the board, personally, I was paranoid of doing anything during first install so I hooked up all of the cables into the board and switched on the machine without the water connected so I had acccess to switch off the power if there was any problems.

Repaired board fitted

The board back in its housing

The washing machine switched on straight away with no flashing lights. Plumbed in the hose after switching it off again and set away two loads. It is now repaired and this is how I fixed my washing machine for £15

 

 

Views – 812